Configuring Meshery Behind istio Ingress gateway

Accessing Workloads behind a ingress-gateway always has been a industry standard practice in Kubernetes setup. It facilitate single entry point for all your services deployed in a production grade Kubernetes. This setup also allows you to leverage the service-mesh functionality of implementing policies and have a better authz and authn to the deployed services. Meshery is no different, you can configure it to be accessed through ingress gateway. Let’s see how can we configure it.

Prerequisite :

1. Kubernetes is up and running.
2. Ingress controller is installed and Ingress-gateway is provisioned (we will be taking istio into account in this example and it is installed in istio-system Namespace)
3. Meshery is installed in your Kubernetes cluster (Preferably in meshery namespace)

See in Action:

Step 1: Prerequisite check

Lets see if everything mentioned in prerequisite is fulfilled

$ kubectl get svc -n istio-system                                                           
NAME                   TYPE           CLUSTER-IP   EXTERNAL-IP   PORT(S)                                      AGE
istio-ingressgateway   LoadBalancer   10.3.9.186   20.204.19.97    15021:30305/TCP,80:32107/TCP,443:32436/TCP   37d

We have ingress gateway provisioned.

$ kubectl get po -n meshery                                                                 

NAME                                    READY   STATUS           RESTARTS      AGE
meshery-5cc4489f77-7sbc5                1/1     Running             0          33d
meshery-operator-5db8b6c874-5cdvg       1/1     Running             0          33d
meshery-meshsync-8lb8b6y784-6ghnk       1/1     Running             0          33d
meshery-istio-6c56dd44fb-gk6xx          1/1     Running             0          33d

$ kubectl get svc -n meshery                                                                

NAME                   TYPE           CLUSTER-IP   EXTERNAL-IP    PORT(S)          AGE
meshery                LoadBalancer   10.3.9.178   10.5.3.188   9081:31037/TCP   33d

Now we see that Meshery’s core components meshery, meshery-operator, meshery-meshsync, meshery-istio (meshery adapter specific to your servicemesh), and meshery LoadBalance service (meshery) are up. The istio ingress gateway istio-ingressgateway is also up.

Note :

• you can observe that the CLUSTER-IP & EXTERNAL-IP of the Meshery LoadBalancer are private IP (10.5.3.188, 10.3.9.178) that means you can not connect it from the browser or outside of the kubernetes cluster.
• in the other hand if you observe we have got an public ip for the istio-ingressgateway (20.204.19.97) which can be accessed from outside of the cluster.
• Only way to access the Meshery is through our ingress gateway (which is part of ingress controller Istio in this case)

Step 2: Let’s create a istio-Gateway for this meshery, which will facilitate meshey to recive the request from outside of cluster to Meshery.

Tip:
What is istio-Gateway?

Gateway describes a load balancer operating at the edge of the mesh receiving incoming or outgoing HTTP/TCP connections. The specification describes a set of ports that should be exposed, the type of protocol to use, SNI configuration for the load balancer, etc. More information : Istio / Gateway

create a file meshery-istio-gw.yaml and copy paste the below content to the file.

apiVersion: networking.istio.io/v1alpha3
kind: Gateway
metadata:
  name: meshery-gateway
  namespace: meshery
spec:
  selector:
    istio: ingressgateway
  servers:
  - port:
      number: 80
      name: http
      protocol: HTTP
    hosts:
    - "*"

Now let’s apply this manifest in meshery Namespace.

$ kubectl apply -f meshery-istio-gw.yaml

Tip:
Istio gateway is namespace scoped. The gateway listener for meshery listens on port 80.

Step 3: Lets create a virtualService for Istio gateway to reach Meshery Loadbalancer in the kubernetes cluster

Tip: What is virtual service?

A VirtualService defines a set of traffic routing rules to apply when a host is addressed. Each routing rule defines matching criteria for traffic of a specific protocol. If the traffic is matched, then it is sent to a named destination service (or subset/version of it) defined in the registry. More info: Istio / Virtual Service

create a file meshery-istio-vs.yaml and copy paste the below content to the file.

apiVersion: networking.istio.io/v1alpha3
kind: VirtualService
metadata:
  name: meshery
  namespace: meshery
spec:
  hosts:
  - "*"
  gateways:
  - meshery-gateway
  http:
  - match:
    - uri:
        prefix: /
    route:
    - destination:
        host: meshery
        port:
          number: 9081

Now let’s apply this manifest in meshery Namespace.

$ kubectl apply -f meshery-istio-vs.yaml

Tip: istio virtualService is namespace scoped.

Understanding meshery-istio-vs.yaml

When the request hits the istio ingress gateway (the gateway listener for meshery listens on port 80) with prefix “/” (root) it will forward it to the kubernetes service meshery which exists in meshery Namespace and listing on 9081 (The default port of Meshery)

Step 4: Accessing Meshery

Now you can access meshhery UI with http:/// in this context http://20.204.19.97/

Tip: when you hit http://20.204.19.97/ it will automatically redirect you to

20.204.19.97/provider and you will she the meshery UI as below:

Extras :

You can use fqdn (let’s say meshery.example.com) for accessing meshery. In that case you have to replace "*" field under hosts: section in meshery-istio-vs.yaml and meshery-istio-gw.yaml to meshery.example.com

Find it on Layer5 discuss forum : discuss.layer5.io/t/configuring-meshery-beh..

Credits:

Layer5 - layer5.io

istio- istio.io

Meshery- meshery.io